|
|
|
Pipeline Services
|
|
[Hot Tap Services] [Pipeline Services] [Water and Wastewater]
|
| Safe, Reliable, Onsite Pipeline Services |
| |
 | Hot Taps, Line Stops | 
Bolt-on 3-Way Hot Tap |
| | Pipe Cutting, Beveling |
| | Technical Bolting |
| | Field Machining |
| | Onsite Valve Repairs |
| | Freeze Stops, Hydrostatic Test Freezes |
| | NDT/NDE and Inspection Services |
| | Pipe Isolation, Weld Testing |
| | Standard Pipe Repair Clamps, Enclosures |
| | Composite Wraps |
| | Heat Treating |
| |
Team's Pipeline Split Tee Hot Tap and Line Stop Fittings
Fittings that meet or exceed code requirements for ANSI/ASME B 31.4 and 8, plus DOT 192 and 195 Federal Regulations for Gas/Liquid Pipelines are available from Team
| | Compatible with existing hot tapping/plugging equipment | 
24" Freeze Stop |
| | Can be utilized for either hot tapping or line stopping |
| | Split tee fittings eliminate alignment problems |
| | There is no potential for weld to penetrate the tapping area |
| | Allows for maximum hot tap size |
| | Size-on-size fittings normally are available off-the-shelf |
| | Full range of reducing branch sizes available |
| | Greater wall thickness |
| | Higher allowable stresses |
| | More reinforcement area |
| | Special fittings are available for any size, flange rating, temperature, pressure, process, or material |
|
| Teams's Pipeline Completion Flanges |
| |
| | Allow completion plug to be set safely at the positive-stop set point |
| | Eliminate need for check valves to equalize pressure across the completion plug |
| | Can be rebuilt on-line |
| | Can be safely utilized to re-enter the line |
| | Are easily resealed if needed |
|
| Teams Offers a Complete Range of Sealing Elements |
| |
| | Maximum pressure ranges: 1480psi | 
Double 22" Linestop, Bypass |
| | Available in sizes 3" through 36" |
| | Available drilled, ground-to-size, unground |
| | Recommended for temperatures to
350° F |
| | Reinforced for higher pressures |
| | BUNA-N materials standard |
| | Viton, EPDM, Aflas also available |
| |
| Also Available From Team |
| |
| | Purge and equalization fittings |
| | Completion plugs with scarfed nipples |
| | Flow-through plugs with guide bars |
|
| Team Also Provides Customers GUL Wavemaker® and Digital Radiography Pipeline Inspection Services |
|
| Advantages of Long Range GUL Pipeline Inspection: |
| |
| GUL is a long range ultrasonic technique for surveying pipelines |
| Test range 250 feet (+/-) from a single test point |
| Detects internal or external metal loss |
| Sensitive to metal loss down to 3% of pipe wall cross-section |
| Discriminates between flaws and pipe features (welds, bends, supports) |
| Effective on hot pipe with the line in service |
| Inspects 100% of the pipe within the diagnostic length of the test |
| Pulse provides information of features, position, approximate sizes of defect |
| GUL's sophisticated analysis aids interpretation of results |
| Operator's interpretive skills are key to successful GUL inspections |
|
Digital Radiography Exposure |
| |
| Advantages of Digital Radiography: |
| |
| Processing time for DRT is less than 1 minute per image compared to more than 30 minutes for film |
| Film cost is eliminated - imaging plates are reusable |
| No processing chemicals to handle or dispose |
| No darkroom required |
| Low energy sources |
| Exclusionary, DRT Zone is greatly reduced |
| Digital images are electronically measured, stored, managed, and transmitted |
|
HOME
COMPANY
CASE HISTORIES
MSDS
LOCATIONS
INVESTORS
EMPLOYMENT
EMPLOYEE TRAINING
CONTACT
Team Industrial Services
P.O. Box 123
Alvin, TX 77512
1-800-662-8326
| |
